Cimarron's new American model!

[mtmarfield]

      Greetings...

   Crappy resolution, but...

                     M.T.M.
                    5-26-24

[Johnson Barr]

 Speed your 'play' problem is not unusual as even original S&W top breaks had this problem. So how did the S&W factory solve this problem?

I've spent a lot of time with original No.2 frame SA's and DA's. More parts than you would imagine are interchangeable even with productions dates 40 years apart. The factory adjustment was the shaft diameter of the barrel latch screw. I have measured no less than 4 different shaft diameters on the No. 2 frame top breaks that I have. That difference is the adjustment between the barrel latch/rear sight and the barrel latch lugs on the frame. Smaller shaft diameters make the lockup looser and the larger shaft diameters make the lockup tighter. I have no idea if Uberti offers latch screws with different shaft diameters to 'tune' the lock-up of any of the Uberti made top breaks. 

The  posted pic is of a pair of Second Model 38 SA framed (dated to 1881 and 1883) revolvers with Third Model 38 DA 5" barrels and Fourth Model 38 DA cylinders (post 1900). The better metallurgy in the post 1900 cylinders makes the light smokeless powder loads I create much safer to shoot. Light loading is to not abuse and be more gentle on the BP frames

[mtmarfield]

      Greetings, All!

   Heads-up.

               M.T.M.
              5-29-24

[mtmarfield]

      Greetings!

   More range time. The little Ideal / Lyman #429348 is a winner on the target!

                    M.T.M.
                   7-02-24

[mtmarfield]

      Greetings!

   And, the Old West Moulds #432-205 "Anderton" bullet...

                     M.T.M.
                   7-02-24
       

[DeaconKC]

Looks like a good load and better shooting!

[mtmarfield]

      Greetings, DeaconKC!

   Thanks, but the trigger is still a real bear. I'm thinking of sending it out to an appropriate Gunsmith. I still want that 8" barrel...! I've been thinking that the Ideal #429348 needs a faster powder; Bullseye or TiteGroup.

                     M.T.M.
                   7-03-24

[Tuolumne Lawman]

My American Model Cowboy Chronicle article, part One. Starting on page 43.

https://www.sassnet.com/uploads/downloads/cowboychronicle/2024/JulyChronGO2024.pdf

[Hair Trigger Jim]

Nice article.  I always enjoy reading your write-ups.

Nice cartridges too.   

[DeaconKC]

I too, enjoyed it a lot.

[Tuolumne Lawman]

Thanks!

[Abilene]

I'm holding off because I want to read it in the hard copy and I won't have that until next week.

[44caliberkid]

I appreciate that Cimarron does other calibers like 44 Russian, 44 Special and 44-40, not just 45 Colt and 357 like Taylor's and Co.

[Tuolumne Lawman]

Part 2 will be in the October Chronicle.  Tune in!

[Tuolumne Lawman]

I have to say, I really enjoy shooting it.  It is tied with my Anderson 1860 .44 Colt conversions.  My answer is to use the 8" American and one 5.5a" Anderson.  I shoot .44 Colt, as that's all the 1999 vintage Andersons shoots.  I shot them at two matches so far (though one was a fun shoot), and going to a monthly match in a couple weeks, then the End of Track annual at the end of October.